Page 288 - CITS - Electrician - Trade Practical
P. 288

ELECTRICIAN - CITS


                                             MODULE 17: Estimating and Costing



           EXERCISE 104 : Plan and carry out Domestic, Commercial,

                                       Industrial  and  Multi-storeyed  building
                                       Workshop


            Objectives


           At the end of this exercise you shall be able to:
           •  draw and construct the circuit of domestic wiring
           •  draw and construct the circuit of industrial wiring
           •  draw and construct the circuit multi storied commercial building wiring.
           Requirements


           Tools/Instruments
           •  Insulated combination pliers 150 mm   - 1 No                 18mm                  - 20 Nos
           •  Side cutting pliers 150 mm          - 1 No                   32mm                  - 26 Nos
           •  Screw driver set 100 mm             - 1 No       •  ICTP main switch 3-phase
           •  Poker 250 mm                        - 1 No          60A, 415V                      - 1 No
           •  Hacksaw 300 mm                      - 1 No       •  Main bus bar chamber
           •  Measuring tape 15 mtr               - 1 No          3-phase 60A 415V               - 1 No
           •  Ballpeen hammer 100 gm              - 1 No       •  ICTP main switch
           •  Electrician’s knife 75 mm           - 1 No          3-phase 16A 415V               - 1 No
           •  Multimeter digital                  - 1 No       •  Phase change over switch
                                                                  3-phase 16amps 415V            - 1 No
           Materials
                                                               •  ELCB/RCCB
           •  PVC Insulated flexible copper wire                  100mA 16amp 240V/400V          - 1 No
              1.5 mm²                             - 11 mtr.    •  PVC copper cable
           •  PVC conduit pipe 19 mm              - 3 mtr.        1.5 sqmm cable 600V            - 0.3 coil
           •  PVC junction box 3 way 19 mm        - 1 No.      •  MCB 6amp 240V                  - 4 Nos.
           •  PVC junction box 4 way 19 mm        - 2 Nos.     •  Sheet metal box for fixing the
           •  PVC round box 80*25 mm              - 3 Nos.        MCB,ELCB & phase change
           •  PVC gang box 2”*2”                  - 3 Nos.        over switch with indicator     - 1 No
           •  Distribution board 12”*10”          - 1 No.      •  PVC channel 25mm x 12          - 4 Length
           •  SPST switch 6A, 250V                - 6 Nos.     •  PVC channel 25mm elbow
           •  Three pin socket 15A, 250V          - 3 Nos.        inner & outer                  - as reqd
           •  DPIC switch 6A, 250V                - 1 No.      •  SPT switch, flush type 6A, 240V   - 12 Nos
           •  MCB 6A, 250V                        - 3 Nos.     •  Fibre plugs                    - as reqd.
           •  ELCB 25A, 30mA,250V                 - 1 No.      •   Metal screws for plug
           •  Steady batten holder 6A, 250V       - 3 Nos.        20mm, 25mm, 35mm x No.6        - as reqd.
           •  Lamp 100W, 250V                     - 3 Nos.     •   PVC round block - 25 x 75 mm   - 8 Nos.
           •  Elbow 20 mm                         - 2 Nos.     •  Two plate ceiling rose - 6A 240V   - 6 No
           •   Saddle 20 mm                       - 20 Nos.    •  Insulation tape 5m 20mm        - 1 Roll
           •  Wood screw                                       •  Bare copper wire 10SWG
                   12mm                           - 40 Nos        & 16SWG                        - as reqd













                                                           271

 CITS : Power - Electrician & Wireman - Exercise 103
   283   284   285   286   287   288   289   290   291   292   293